Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Powertrain Guides
- Ford Mustang Gt 1996 to 2004: How to Replace Spark Plugs and Ignition Coils
Step by step instructions for do-it-yourself repairs
Browse all: Powertrain Guides
HOW TO: CHANGING SPARK PLUGS 99-04
#1
HOW TO: CHANGING SPARK PLUGS 99-04
This write up was done by mself52...
If you guys are like me when you look at the engine when your about to change the spark plugs it looks very intimidating and looks hard... but in reality its very simple and takes bout an hour to 90 mins to change them with the right tools and a little direction... so i figured id do a write up for you guys....
to start with you DO NOT have to remove the fuel rail.... the only thing that you need to remove is the air intake from the throttle body...this is so you can get to the number 3 plug that is right under it...
tools needed include:
1) 5/8" spark plug socket
2) 6" extension
3) 9/32" socket
4) small tube of anti seize
now here is a picture with what you will actually be removing
you remove that small 9/32" bolt and that allows you to pull the coil from the plug hole it might be stuck good so just wiggle it around and pull but it will pop out...the only plug that you need to unhook the harness from the coil is on the number 4 plug which is on the passenger side at the back next to the firewall....its too much of an angle to bend the coil and get it back in without unhooking the harness...
after removing the coil this is what it looks like
and this is where the spark plug is
now before removing the spark plug if you look inside the hole there will be alot of debris that you should blow out with either canned air or a air compressor....
now that the plug is out take your new plug and put a few dabs of anti seize on the threads and smear it on all the threads... then wipe the excess off with a towel... now put the new plug in... hand tighten it and then snug it but DO NOT over tighten it because this is aluminum and will strip if you try and torque it too much... just snug it and then a slight bit tighter
now put the end of the coil back in the hole and wiggle it around while pressing down untill it is back in place and the bolt hole should line up and you put the bolt back in....
repeat on all plugs....
TIPS:
if you remove any of the fuel injector harness please becareful there is a little red gasket inside each plug so if it falls out make sure you put it back in before moving on.... and on the number 4 plug do yourself a favor and remove the coil plug and the fuel injector plug to give you room and so that when you goto put the coil back in over the plug you can manevuer it back in....
hope this helps and good luck
If you guys are like me when you look at the engine when your about to change the spark plugs it looks very intimidating and looks hard... but in reality its very simple and takes bout an hour to 90 mins to change them with the right tools and a little direction... so i figured id do a write up for you guys....
to start with you DO NOT have to remove the fuel rail.... the only thing that you need to remove is the air intake from the throttle body...this is so you can get to the number 3 plug that is right under it...
tools needed include:
1) 5/8" spark plug socket
2) 6" extension
3) 9/32" socket
4) small tube of anti seize
now here is a picture with what you will actually be removing
you remove that small 9/32" bolt and that allows you to pull the coil from the plug hole it might be stuck good so just wiggle it around and pull but it will pop out...the only plug that you need to unhook the harness from the coil is on the number 4 plug which is on the passenger side at the back next to the firewall....its too much of an angle to bend the coil and get it back in without unhooking the harness...
after removing the coil this is what it looks like
and this is where the spark plug is
now before removing the spark plug if you look inside the hole there will be alot of debris that you should blow out with either canned air or a air compressor....
now that the plug is out take your new plug and put a few dabs of anti seize on the threads and smear it on all the threads... then wipe the excess off with a towel... now put the new plug in... hand tighten it and then snug it but DO NOT over tighten it because this is aluminum and will strip if you try and torque it too much... just snug it and then a slight bit tighter
now put the end of the coil back in the hole and wiggle it around while pressing down untill it is back in place and the bolt hole should line up and you put the bolt back in....
repeat on all plugs....
TIPS:
if you remove any of the fuel injector harness please becareful there is a little red gasket inside each plug so if it falls out make sure you put it back in before moving on.... and on the number 4 plug do yourself a favor and remove the coil plug and the fuel injector plug to give you room and so that when you goto put the coil back in over the plug you can manevuer it back in....
hope this helps and good luck
#5
Paragraph two from the above post:
[emphasis added]
Also, as you may have noticed this is an 5-year old "how-to", "...just snug it and then a slight bit tighter." is about the worst advice one could give for an engine known to spit out improperly installed plugs resulting in $100 to $800 repairs.
Get a 1/4" drive torque wrench and torque the plugs to 11-13 lbft. If you absolutely have to make them hand tight plus another 1/16th of a turn...
to start with you DO NOT have to remove the fuel rail.... the only thing that you need to remove is the air intake from the throttle body...this is so you can get to the number 3 plug that is right under it...
Also, as you may have noticed this is an 5-year old "how-to", "...just snug it and then a slight bit tighter." is about the worst advice one could give for an engine known to spit out improperly installed plugs resulting in $100 to $800 repairs.
Get a 1/4" drive torque wrench and torque the plugs to 11-13 lbft. If you absolutely have to make them hand tight plus another 1/16th of a turn...
#6
Sorry, I got to looking at the pictures and missed that line. I do have a torque wrench and will definitely use it.
I would like to be able to monitor my cylinder head temperature. I've seen thermocouples designed for this purpose that look like a ring lug which fits over the spark plug threads. Could such a device be used on this engine? My concern is that with the lead wires coming up out of the hole that the coil wouldn't fit. I don't really want to spend $40 on one and then it not work.
Thanks,
Mike
I would like to be able to monitor my cylinder head temperature. I've seen thermocouples designed for this purpose that look like a ring lug which fits over the spark plug threads. Could such a device be used on this engine? My concern is that with the lead wires coming up out of the hole that the coil wouldn't fit. I don't really want to spend $40 on one and then it not work.
Thanks,
Mike
#8
Sorry, I got to looking at the pictures and missed that line. I do have a torque wrench and will definitely use it.
I would like to be able to monitor my cylinder head temperature. I've seen thermocouples designed for this purpose that look like a ring lug which fits over the spark plug threads. Could such a device be used on this engine? My concern is that with the lead wires coming up out of the hole that the coil wouldn't fit. I don't really want to spend $40 on one and then it not work.
Thanks,
Mike
I would like to be able to monitor my cylinder head temperature. I've seen thermocouples designed for this purpose that look like a ring lug which fits over the spark plug threads. Could such a device be used on this engine? My concern is that with the lead wires coming up out of the hole that the coil wouldn't fit. I don't really want to spend $40 on one and then it not work.
Thanks,
Mike
Last edited by cliffyk; 10-28-2011 at 05:26 AM.
#10
Oh yeah, anti sieze is a must on any spark plug. And LOL at torque wrench. I know a lot of people use them, but on spark plugs, I just crank em down till they are tight.